路由设置网 - 192.168.1.1路由器登录入口设置指南
当前位置: 路由器首页 > 路由器知识 >

路由器的基本配置命令大全

 2013-10-20 21:08  未知  admin  
启动接口,分配IP地址:

  router>

  router> enable

  router#

  router# configure terminal

  router(config)#

  router(config)# interface Type Port

  router(config-if)# no shutdown

  router(config-if)# ip address IP-Address Subnet-Mask

  router(config-if)# ^z

  配置RIP路由协议:30秒更新一次

  router(config)# router rip

  router(config-if)# network Network-Number <--通告标准A,B,C类网-->

  router(config-if)# ^z

  配置IGRP路由协议:90秒更新一次

  router(config)# router igrp AS-Number <-- AS-Number范围1~65535-->

  router(config-if)# network Network-Number <--通告标准A,B,C类网-->

  router(config-if)# ^z

  配置Novell IPB路由协议:Novell RIP 60秒更新一次

  router(config)# ipx routing [node address]

  router(config)# ipx maximum-paths Paths <--设置负载平衡,范围1~512-->

  router(config)# interface Type Port

  router(config-if)# ipx network Network-Number [encapsulation encapsulation-type] [secondary] <--通告标准A,B,C类网-->

  router(config-if)# ^z

  配置DDR:

  router(config)# dialer-list Group-Number protocol Protocol-Type permit [list ACL-Number]

  router(config)# interface bri 0

  router(config-if)# dialer-group Group-Number

  router(config-if)# dialer map Protocol-Type Next-Hop-Address name Hostname Telphone-Number

  router(config-if)# ^z

  配置ISDN:

  router(config)# isdn swith-type Swith-Type <--配置ISDN交换机类型,中国使用basic-net3-->

  router(config-if)# ^z

  配置Frame Relay:

  router(config-if)# encapsulation frame-relay [cisco | ietf ]

  router(config-if)# frame-relay lmi-type [ansi | cisco | q933a ]

  router(config-if)# bandwidth kilobits

  router(config-if)# frame-relay invers-arp [ Protocol ] [dlci ]

  <--配置静态Invers ARP表:

  router(config)# frame-relay Protocol Protocol-Address DLCI [ Broadcast ] [ ietf | cisco ] [ payload-compress | packet-by-packet ]

  -->

  <--设置Keepalive间隔:

  router(config-if)# keepalive Number

  -->

  <--为本地接口指定DLCI:

  router(config-if)# frame-lelay local-dlci Number

  -->

  <--子接口配置:

  router(config-if)# interface Type Port.Subininterface-Number [ multipoint | point-to-point ]

  router(config-subif)# ip unnumbered Interface

  router(config-subif)# frame-lelay local-dlci Number

  -->

  router(config-if)# ^z

  配置标准ACL:

  router(config)# access-list Access-List-Number [ permit | deny ] source [ source-mask ] <-- Access-List-Number 范围:1~99标准ACL;100~199扩展ACL;800~899标准IPB ACL;900~999扩展IPB ACL;1000~1099 IPB SAP ACL;600~699Apple Talk ACL-->

  router(config)# interface Type Port

  router(config-if)# ip access-group Access-List-Number [ in | out ]

  router(config-if)# ^z

  配置扩展ACL:

  router(config)# access-list Access-List-Number [ permit | deny ] [ Protocol | Protocol-Number ] source source-wildcard [ Source-Port ] destination destination-wildcard [ Destination-Port ] [ established ]

  router(config)# interface Type Port

  router(config-if)# ip access-group Access-List-Number [ in | out ]

  router(config-if)# ^z

  配置命名ACL:

  router(config)# ip access-list [ standard | extended ] ACL-Name

  router(config [ std- | ext- ] nacl)# [ permit | deny ] [ IP-Access-List-Test-Conditions ]

  router(config [ std- | ext- ] nacl)# no [ permit | deny ] [ IP-Access-List-Test-Conditions ]

  router(config [ std- | ext- ] nacl)# ^z

  router(config)# interface Type Port

  router(config-if)# ip access-group [ACL-Name | 1~199 ] [ in | out ]

  router(config-if)# ^z

  配置DCE时钟:

  router# show controllers Type Port <--确定DCE接口-->

  router(confin-if)# clock rate 64000 <--进入DCE接口设置时钟速率-->

  router(config-if)# ^z

  配置PPP协议:

  router(config)# username Name password Set-Password-Here <--验证方建立数据库-->

  router(config)# interface Type Port

  router(config-if)# encapsulation ppp <--启动PPP协议-->

  router(config-if)# ppp outhentication [ chap | chap pap | pap chap | pap ] <--选择PPP认证-->

  router(config-if)# ppp pap sent-username Name password Password <--发送验证信息-->

  router(config-if)# ^z

!版权声明:本文《路由器的基本配置命令大全》于2013-10-20 21:08发布在www.002cn无线之家;

转载请注明出处:http://www.002cn.cn/know/363.html

站长推荐

192.168.50.1手机登录页面

192.168.50.1 是本地、私有或网关 IP 地址。通常用在华硕ASUS路由器默认登录入口。192.16...

2021-09-10 192.168.0.1

无线路由器如何取消隐藏无线名称

隐藏的WIFI是对手机或电脑不可见的,如果需要连接至隐藏的WIFI,我们需要手动添加其...

2021-07-24 路由器知识

192.168.31.1小米路由器手机登录设置

小米路由器的默认登陆入口是192.168.31.1;我们只需要在手机或电脑的浏览器中打开IP地...

2021-07-08 192.168.0.1

魔术家R100路由器设置登陆地址和密码

当你把魔术家R100路由器重置后,你可能需要使用以下信息登录路由器并重新设定网络才...

2021-04-27 路由器设置

为什么192.168.0.1无法打开路由器管理界面

默认情况下,路由器的IP地址配置为192.168.0.1或类似的名称;如果你无法通过192.168.0.1进...

2021-04-17 192.168.0.1

光猫与无线路由器桥接上网步骤

不少朋友询问光猫能不能与无线路由器进行桥接上网?今日就抽点时间教大家如何使用...

2021-04-07 路由器上网

两个Buffalo路由器之间如何建立有线桥接网络

两个Buffalo路由器如何设置桥接模式上网?在连接到Internet网络的主路由器和辅助路由器...

2021-03-12 路由器上网

trendnet无线路由器登录管理密码及上网设置

本文提供您Trendnet无线路由器的默认登录信息。以及如何设置Trendnet路由器,不同的路由...

2021-03-01 路由器设置